Accueil - Produits - Programmeur De Clef - EWS Editor For BMW Version 3.2.0 B
« Revenir

EWS Editor For BMW Version 3.2.0 B

Numéro de l'article. SK74-B
Out of Stock
Achat immédiat:€69.00 
Les frais d'envoi:
Livraison Gratuite   Poste Ordinaire Service 
Délai de livraison estimé: 10-20 jours de travail. Détails
Poids:
0.2KG
Paquet:
17cm*15cm*2.5cm      ( Inch:6.68*5.89*0.98 )
Retours:
Retour de remboursement dans 7 jours, l'acheteur paie les frais de retour.Lire les Détails »
EWS Editor For BMW Version 3.2.0 B is designed to work with factory anti-theft system (immobilizer) EWS. Immobilizer EWS has been installed on the BMW AG vehicles since 1996. Cars such as BMW 3 series (E46), 5 series (E39), 7 series (E38), X3 (E83), X5 (E53), Z4 (E85) and other vehicles of BMW AG - MiniCooper, Rover 75, Range Rover are equipped with this system.

EWS Editor For BMW Version 3.2.0 B

Product Description:


This device is designed to work with factory anti-theft system (immobilizer) EWS. Immobilizer EWS has been installed on the BMW AG vehicles since 1996. Cars such as BMW 3 series (E46), 5 series (E39), 7 series (E38), X3 (E83), X5 (E53), Z4 (E85) and other vehicles of BMW AG - MiniCooper, Rover 75, Range Rover are equipped with this system.

USB interface
No AC/DC adaptor required
All modifications of factory immobilizers are supported: EWS1, EWS2, EWS3, EWS3+
Reading and writing of EWS3 and EWS3+ via k-line
Automatic version determination of EWS via reading the memory dump
Adding new keys
Adding used keys (if key’s password is available)
Resetting used keys into a “new” state (if key’s password is available)
Recovery of key's synchronization (matching keys)
Blocking and releasing vehicle access via the specific key
Recovering of coding data (vehicle's specific information)
Changing EWS parameters (product number, date of manufacturing, etc)
Resetting used EWS3 (loading default values)
Changing VIN number which is contained in EWS unit
Changing VIN number which is contained in key (since 1998)
Changing mileage in EWS (contained in EWS since 1998 and on)
Changing mileage in key (contained in key since 1998 and on)
Software creates log-file of read and written keys, which helps to exclude the error of casual blocking key with password, etc.
Possibility of control and recovery of variable part of matching code for EWS and engine control unit DME/DDE
Configuring new transponders PCF7930 and PCF7935 to work with EWS unit.
Supports FSU (Firmware Secure Update) from Internet.

Except processors with mask set D47J. EWS unit equipped with this processor has read protection, attempt of reading the processor with this mask set results EEPROM data loss. To recover the data in EWS3 unit with processor (D47J) use the function [ Reset to factory defaults ]
 

Supported cars:

3 series (E46)
5 series (E39)
7 series (Е38)
X3 (E83)
Х5 (Е53)
Z4 (E85)
Range Rover Vogue
Rover 75
Mini Cooper

Checking of MOTOROLA processor mask set which is used in some EWS units
Before proceed to reading of EWS data using the function [ EWS Read ]
Read the marking (maskset) plotted on processor (picture):
1. Mask set D47J -old versions of EWS1, EWS2 and EWS3 hw:2 sw:5. Refer to #Recovering of EWS
2. Mask set D46J -new versions of EWS3 and EWS3+. This processor does not contain unpleasant
 

Driver Installation:

1. Start EWS_EditorInst.exe file
2. Select installation path. The default path is C: Program Files AvtoTools EWS_Editor
3. Please connect device to USB
4. Install drivers from folder C:Program FilesAvtoTools EWS_EditorDrivers Reading EWS

1. Unplug and detach EWS3 unit from the car. Attaching points of EWS3 unit can be found in BM
2. Take the plastic case off from EWS3
3. Connect EWS3 to the socket of the cable for reading/writing EWS3
4. Reassure that in EWS Editor programme type of EWS is switched to Auto
5. In EWS Editor programme select [ Read EWS ] function
6. Programme tries to read contents of EWS3 four times, meantime you must touch test point on the PCB (printed circuit board) of EWS3 with probe (see picture below), hold it on the test point untill reading procedure starts.
7. If the connection established successfully, progress bar appears:
8. Remove the probe off the PCB


WARNING!!!
1. Selecting wrong test point you may damage or break EWS3 unit! Be very attentive!
2. PCB of EWS3 unit is covered with non-conductive compound, it may lead to poor contact of probe with test point on the PCB of EWS3 unit, and you will be unable to connect to EWS3 unit.

Writing EWS
1. Connect EWS3 to the socket of the cable for reading/writing EWS3
2. Perform all the necessary changes
3. Select [ Save EWS ] function in EWS Editor programme

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------



Quel est le sens de QC marque sur produit?

1. Le QC marque signifie que ce produit a passé letest de notre ingenieur.
2. Le QC marque signifie que le produit est de notre société.
3. Le QC marque signifie que le produit obtiendra la garantie.


Attention les risques viennent de la douane:

1. Les colis DHL envoyés vers l'outre-mer de la france (Martinique, Réunion, Guadeloupe etc. ) ont peut-être des frais de douane, merci de votre compréhension.
2. Certains produits speciaux vers la France: Lexia 3 PP2000, Renault Can Clip, Multidiag Pro, Multidiag Actia, MB Star série etc. le mode de livraison est Yanwen EMS, délai de livraison est 8-13 jours.


Contact informations:

Email: sales@diyobd2.fr
Skype: diyobd.fr
WhatsApp: +86 15826108827


Online service support
Facebook: https://www.facebook.com/diyobd2.fr

Si vous avez des questions, n'hésitez pas à nous contacter.
Donnez votre avis
* Classment:
    Sélectionner les étoiles de la classification svp.
* Votre prénom et nom:
* Votre adresse e-mail:
* Afficher les avis:
*Code de vérification:
          Aucun droit? Obtenir un nouveau code de vérification
 
Dites-nous ce que vous pensez de cet article et partagez vos opinions avec d'autres personnes. S'il vous plaît assurez-vous que votre avis ne porte que sur ce point. Tous les commentaires sont modérés et seront réexaminées dans un délai de deux jours ouvrables. Commentaires inappropriés ne seront pas affichés.
Après-vente et questions: Contactez notre Service à la clientèle. (Un représentant clientèle vous contactera pour vous).
S'il vous plaît Inscrivez en premier si vous voulez plus tard modifier ou gérer les commentaires transféré par vous-même.
Bookmark It