Accueil - Produits - [Master] - OBD2 Diagnostic Appareil - MST-12000 Universal Automotive Test Platform and ECU Signal Simulation
« Revenir

MST-12000 Universal Automotive Test Platform and ECU Signal Simulation

Numéro de l'article. SP164
Manufacturer: Master
In Stock
Achat immédiat:€1,899.00 
Quantité:
  
Les frais d'envoi:
   Livraison Express Service 
Délai de livraison estimé: 3-5 jours de travail. Détails
Poids:
10.0KG
Paquet:
125cm*61cm*61cm      ( Inch:49.09*23.95*23.95 )
Retours:
Retour de remboursement dans 7 jours, l'acheteur paie les frais de retour.Lire les Détails »
Télécharger des fichiers connexes:
  mst-12000-universal-automotive-testr-english-manual.doc  (12,726.1K)
MST-12000 Universal Automotive Electrical and Electronic Bench

MST-12000 Universal Automotive Test Platform and ECU Signal Simulation
 
Feature of MST-12000 Automotive Test Platform:

 
1. The all cars crankshaft signal simulation expert:
 
Twelve way set arbitrary waveform output, can produce all of today's car engine crankshaft, camshaft signal (Hall, magnetoelectric, photoelectric signal), waveform data will be pre-served by computer for long term.
 
2. All magnetoelectric crankshaft signal will be isolated by transformer, ensure no interference between signals.
 
3. The whole series of car sensor signal simulation expert:
 
The rotational speed signal, the speed signal (Hall, magnetoelectric, photoelectric signal), the ABS wheel speed signal, oxygen sensor signal, throttle valve, the accelerator
 pedal signal, air flow meter, the intake pressure sensor (analog, digital), knock sensor etc signals simulation.
 
4. The All cars actuator drive experts:
 
Tachometer, odometer, blower control module, ignition module, frequency and pulse width control solenoid valve, car audio power amplifier.
 
5. The All cars actuator simulation expert
 
Diesel common rail injector, rail pressure control valve, ignition coil, injector, idle stepper motor, ultrasonic generator,etc actuator simulation.
 

MST-12000 Automotive Test Platform Fuctions:
 
The user can set crankshaft of different types according to different independent engine control system
 1). The signal output (applicable to all car models of computer driven)
 2). Automatic transmission input/output shaft signal simulation
 3). Set to write into the waveform data directly
 4). Engine revolving speed signal output
 5). The speed signal output (hall signals, magnetoelectric)
 6). Three or four channel ABS wheel speed signal output
 7). Computer board working current test
 8). EGR solenoid valve simulation
 9). CANP Canister Purge solenoid simulation
 10). Tachometer simulation and drive
 11). Blower control module driver
 12). Auxilliary air regulator simulation       
 13). Stepping motor simulation(Four/Six line)
 14). Fuel injector simulation
 15). Ignition coil simulation
 16). The ignition module simulation
 17). Reversing radar (ultrasonic) probe drive
 18). The shift valve of automatic transmission simulation
 19). Diesel injector simulation
 20). Rail pressure regulator simulation
 21). Shift quality valve simulation
 22). Oil pressure regulating valve simulation
 23). Water temperature, air temperature, outdoor temperature and evaporation temperature sensor signal simulation
 24). Oxygen sensor signal simulation (manual)
 25). The accelerator pedal double channel signal simulation       
 26). Throttle signal simulation
 27). CANP Canister purge solenoid simulation
 28). Air flow meter,manifold Absolute Pressure Sensor (analog, digital) signal simulation
 29). Brake switch simulation
 30). Clutch switch simulation
 31). A\C request signal simulation
 32). A\C relay simulation
 33). Fule pump relay simulation
 34). Radiator fan relay simulation
 35). Audio signal output, power amplifier drive
 36). Steering pressure switch simulation
 37). Fuel injection pulse width measurement
 38). Central door lock server simulation
 39). Anti theft resistance simulation
 40). Knock sensor signal simulation
 41). Computer board working current test
 42). User extensional functions
 

MST-12000 Instrument parameters:
 
1. Can set the waveform output: It can set twelve channels waveform output arbitrary, can simultaneously output crankshaft 1 º angle signal, the signal of cylinder detection,
 TDC of cylinder 1 signal, camshaft signal, phase precision.This machine is applied to crankshaft and camshaft signal simulation of all vehicles worldwide; also applies
 to the crankshaft and camshaft signal input, output simulation,and all of the automatic transmission input, output shaft signal simulation; ABS three or four channel wheel
 speed signal simulation; computer set the waveform, and waveform can be long-term preservation;
 2. Output signals: magnetoelectric signals, hall, photoelectric signal;
 3. Duty cycle drive: duty cycle 1 ~ 99% continuous adjusting,frequency of 11 files regulation
 4. The sensor signal simulation: resistance of 100 Ω ~10000 Ω voltage 0V~5V × 4 0V~1.5V   
 5. Actuator drive simulation: 69 channel output simultaneously
 

MST-12000 Instrument application:
 
1. Automobile sensor dynamic diagnosis, automobile engine, transmission, ABS, air conditioning, anti theft  and  other  computer repair,  auto teaching AIDS model driven, automobile production development;
2. The utility model is suitable for Germany, the United States, Japan, South Korea, and other domestic mini models etc hundreds of models;
 
Operation panel profile:
 
Output port: the above of the port said the abbreviation of the port name and the below is the port number (1-192) a total of 192 output ports.




INJ1-INJ12 (port 81-86,113-118): making 1-12 cylinder injector and injection time (MS) (12V,gasoline)



SV1 (H) -SV6 (H) (port 129-134), SV1 (L) -SV6 (L) (port 145-150) diesel injector signal output (24V)




Analog output:
 
 
IATS: ( Port155 ) air charge temperature sensor 0-5V
 
THW:( Port156) water temperature sensor 0-5V
 
TPS1:( Port143) Throttle position sensor signal simulation 0-5V
 
TPS2: ( Port144) Throttle position sensor signal simulation ratio control 0-5V,used to adjust two throttle signal output ratio. If two throttle position sensor signals need to be 2:1, then adjust TPS1 output voltage to 1v, TPS2 0.5V. And then adjust the voltage of TPS1,  two signals can be 2:1.
 
MAP:( Port158) Air intake pressure sensor signal simulation 0-5V
 
MAF:( Port57) Air flow meter signal simulation 0-5V
 
EGOS1:( Port141) Oxygen sensor signal simulation 0-1V
 
EGOS2:( Port 142) Oxygen sensor signal simulation 0-1V
 
LDFT:( Port151) Boost pressure sensor 0-5V
 
RPS; ( Port152) Fuel rail pressure sensor 0-5V
 
OPTS:( Port153) oil pressure sensor 0-5V
 
FTS: ( Port154) oil temperature sensor





 

Digital signal output:
 

 DS1:( Port135) knock sensor 1 signal simulation

 DS2:( Port136) knock sensor 2signal simulation











CH0-CH7: ( Port41-48) The camshaft & crankshaft square wave signal
CH8-CH11: ( Port33-40) The camshaft & crankshaft ac signal( This feature requires a PC through good software calibration input signal of the crankshaft. Click on a host "OUT" knob it can be output )




Components of simulation:
 

 IACV: ( Port140 ) Idle speed control valve displacement simulation

 PMR: ( Port135 ) pump relay fuel pump relay

 EFI: ( Port136 ) main relay

 MIL1: ( Port121) ] indicator light1

 MIL2: ( Port122 ) indicator light 2

 EGR: ( Port123 ) exhaust gas recirculation

 EVP: ( Port125 ) CHARCOAL CANISTER-PURGE VALVE

 A\C: ( Port126 )Air Conditioner Relay

 FAN1: ( Port127) ELectric fan relay 1

 FAN2: (Port128) ELectric fan relay 2

M4: ( M4Port Area, Port93、94、109、110 ) Four wire stepper motor simulation

M6: ( M6Port Area, Port95、96、111、112) Six line stepper motor simulation




ZME1: ( Port79-80 ) Rail pressure regulator 1

ZME2: ( Port63-64 ) Rail pressure regulator 2 ( standby application )


Ignition coil and ignition module simulation (B1-B6)
IG1 (L) -IG4 (L): (port 103-106) ignition coil and ignition module, indicator light negative

trigger


IG1 (H) -IG6 (H): (port 87-92) ignition coil and ignition module, the indicating lamp is triggered
IGF (port 139) ignition feedback signals


IGC1, IGC2: (port -107-108) ignition coil simulation:


Electromagnetic valve simulation:

SOL1 - SOL8,49 (port 65-65-56)(12V)



SOL1 (L) -SOL6 (L) (port 80-82,97-99) (24V)
SOL1-SOL6 (port 73-78,57-62)






The power supply part:


OBD diagnosis:


Digital Signals:


Triggered Relay:

Tachometer Signal:



Wave setting software installation and use method:

Firstly,pls put the CD into the computer cd-rom,and open the software then copy the "simulation expert official version.Exe" file to the computer desktop and double-click the file,Double-click to open the desktop icon, the followings appear:



Click on the "signal editing", enter the signal editing interface.




Any set zone can be setted the waveforms you need arbitrary,CH0 is the tachometer channel, every 1 revolutions of the engine crankshaft, the channel 6 pulse.
CH1 -- CH7 is mainly used for square wave set, CH8-CH11 is mainly used for sine wave set. After the waveform set, input the waveform end position that we set the  in the "hase" menu.
For example: editing a 36-2 square wave crankshaft signal in CH1, and repeat the cycle.
In the CH1 click 36 pulse continuous.



2. In thirty-sixth pulse position as the phase 72. In the "hase" input "72"



3. Between 36 pulse,remove two pulse at random and continuously, you can get 36-2 signal.



4. With the end phase number of 72\6=12, that means every 12 phase then click a pulse in CH0 ,can be set to the tachometer signal.


Packing list:

1set x The MST-12000 sensor signal simulator
60 pieces x The data line
1 piece x Power line
1 piece x The USB data line
1piece x Data disc

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------



Quel est le sens de QC marque sur produit?

1. Le QC marque signifie que ce produit a passé letest de notre ingenieur.
2. Le QC marque signifie que le produit est de notre société.
3. Le QC marque signifie que le produit obtiendra la garantie.


Attention les risques viennent de la douane:

1. Les colis DHL envoyés vers l'outre-mer de la france (Martinique, Réunion, Guadeloupe etc. ) ont peut-être des frais de douane, merci de votre compréhension.
2. Certains produits speciaux vers la France: Lexia 3 PP2000, Renault Can Clip, Multidiag Pro, Multidiag Actia, MB Star série etc. le mode de livraison est Yanwen EMS, délai de livraison est 8-13 jours.


Contact informations:

Email: sales@diyobd2.fr
Skype: diyobd.fr
WhatsApp: +86 15826108827


Online service support
Facebook: https://www.facebook.com/diyobd2.fr

Si vous avez des questions, n'hésitez pas à nous contacter.
Donnez votre avis
* Classment:
    Sélectionner les étoiles de la classification svp.
* Votre prénom et nom:
* Votre adresse e-mail:
* Afficher les avis:
*Code de vérification:
          Aucun droit? Obtenir un nouveau code de vérification
 
Dites-nous ce que vous pensez de cet article et partagez vos opinions avec d'autres personnes. S'il vous plaît assurez-vous que votre avis ne porte que sur ce point. Tous les commentaires sont modérés et seront réexaminées dans un délai de deux jours ouvrables. Commentaires inappropriés ne seront pas affichés.
Après-vente et questions: Contactez notre Service à la clientèle. (Un représentant clientèle vous contactera pour vous).
S'il vous plaît Inscrivez en premier si vous voulez plus tard modifier ou gérer les commentaires transféré par vous-même.
Mots-clés de produit:   obd2 tool   ECU tester   MST-12000 tester  
Bookmark It